News

How do you use the oil in the right way

• 2019-12-30
• 0

How to use the oil heater You use the right way oil it

Electric oil heater for living room heating, the air should be as close to the location of convection, so both warm and power. As the radiator type oil heater in the work of the surface temperature can be as high as 85 degrees Celsius, for the bedroom heating, should try to avoid the person's head. If you have children in your home, place them in a place that is not easily accessible to children, or add protective equipment around them to prevent children from burning. In the use of electric oil heater, be sure to stand upright, because it is through the lower end of the heat pipe to heat the surrounding heat transfer oil, heat conduction oil in the flow tube to transfer heat. If the inverted, flat or oblique release, it will cause air burning, burning heat pipe.

1, the proper use of thermostat

To adjust the temperature, turn the thermostat knob clockwise to the maximum position, turn on two power switches, the maximum output state of the machine, heating up about 5 minutes, gently tapping the upper surface of the shell with the back of the hand , If feel the temperature suitable, the knob counter-clockwise rotation gently, transferred to a certain location, can provide people with the temperature. The surface of the shell is slightly hot when the temperature is about 65 ℃ -80 ℃. The temperature of the shell is higher than the set temperature, the thermostat will automatically cut off the power to stop heating, the internal heat to continue to release the deposit. The surface temperature dropped 15 ℃, the thermostat contacts will automatically close, heating heating, shell temperature is higher than the set temperature, and automatically power to stop heating. So again and again, the temperature balance.

2, the correct choice of the use of power switch

Oil machine using two sealed electric heating tube as a heating element, two groups of heating tube corresponding to two grades of two selectors. Open the oil machine or indoor temperature is low, while opening the two-stage selector switch, oil Ting machine rapid warming, the shell surface temperature reaches the set temperature after the point, the thermostat automatically cut off the power, this time should choose 1 Or 2-stage power. When the thermostat reset power, the use of lower power heating, and gradually improve the indoor temperature.

3, pay attention to maintaining the sealing room

Electric oil heater heater is the form of air convection to increase the indoor temperature, the indoor temperature and the impact of power on and off. Indoor airtight, room temperature, the heating time is short, long heat dissipation, thus saving energy.

4, the prohibition of coverage

Heater normal work, the shell surface temperature is high, generally set about 80 ℃. Oil temperature control machine is to rely on the mask within the thermostat sheet metal temperature deformation to achieve. If you want to bake clothes, the package will be covered around the heatsink, the covered hot film temperature will be significantly higher than the surface of the bimetal feel the temperature, so easy to burn clothing, and may lead to oil within the casing body heat transfer oil Denaturation, pressure, causing the leakage of hot oil from the seal, and even the shell burst, causing danger.

5, to prohibit the upper and lower inverted or put down electric heating

Oil-specific heat conduction oil inside the casing, after heating a certain internal pressure, in order to ensure normal use when the internal pressure is lower than 0.2Mpa, thermal oil perfusion volume of about 70% of the total, the interior has a larger space. Inverted or tilted, the internal heating tube exposed to the oil, in this case, the heating power may cause over-burning cracks, damage to the heating tube. For this case, the use must pay attention.

6, material selection

The key of the raw materials such as electrical components: adjustable temperature control, thermal fuses, power lines, electric pipes, thermal oil, steel and so choose the best supplier of supply, the plastic parts are used flame retardant material in line with all the safety regulations Testing requirements. (Some manufacturers use the certification is a good material, the actual production is not in line with the requirements of the material, the plate will use a thin 0.4MM or 0.45MM, plastic with flame retardant, electrical components used in the underground factory The quality can not be guaranteed).

Special note is that electric oil can not be used for the bathroom. Although the electric oil heater switch on a marked waterproof plastic cover, but its only waterproof splash and not waterproof steam, for the bathroom will be a certain risk.